Re-map Desk Instructions - Trafficware

When an iCCU-S/S2 system is operating in SDLD/BIU mode, the traffic controller must be remapped for it to see pedestrian calls over BIU. Use the following procedure for Trafficware or similar traffic controllers:

• Configure Detector Rack BIU for Pedestrian Calls (example is BIU#2)

  • Add Detector Rack Device (Need to add the second detector rack to enable the SDLC signaling to it)

    • Main Menu (older Trafficware firmware)
      • Select “1”Controller
      • Select “3” Chan, SDLC
      • Select “7” SDLC Devcs
    • Main Menu (Newer Trafficware firmware)
      • Select “1”Controller
      • Select “3” Chan, SDLC
      • Select “1” TS2 Devcs
    • Move cursor to the right, under Detector 2
    • Select “1” to enable
    • Press “ENTR” key to save

• Detector Rack Re-mapping

  • For Detector BIU 2: Map the input functions Veh Call 17, Veh Call 18, Veh Call 19, and Veh Call 20 to Ped Call 2, Ped Call 4, Ped Call 6 and Ped Call 8, respectively
  • For Detector BIU 3: Map Veh Call 33, Veh Call 34, Veh Call 35, and Veh Call 36 to Ped Call 2, Ped Call 4, Ped Call 6 and Ped Call 8, respectively
  • For Detector BIU 4: Map Veh Call 49, Veh Call 50, Veh Call 51, and Veh Call 52 to Ped Call 2, Ped Call 4, Ped Call 6 and Ped Call 8, respectively
  • On the Trafficware controller Vehicle Call inputs 1-64 are input function numbers 1-64, respectively
  • The Ped Call inputs 1-8 are input function numbers 129-136, respectively
  • For a standard 4 ped phase intersection only input functions 130 (phase 2), 132(phase 4), 134 (phase 6), 136 (phase 8) are used
  • Go to the “IO Logic” menu to re map the functions.
    • Main Menu (older Trafficware firmware)
      • Select “1” Controller
      • Select “3” Chan, SDLC
      • Select “9” IO Mapping
      • Select “1” IO Logic
    • Main Menu (newer Trafficware firmware)
      • Select “1” Controller
      • Select “8” Channel IO
      • Select “7” IO Logic
    • Set according to table (enter the vehicle call function number on the right and the ped call function on the left) (Detector 2 re-mapping shown)

• Press “ENTR” key to save.

• Configure Terminals and Facilities BIU 2 with Flash Status

  • Re-Map Flash to Output Logic 1 function

    • Main Menu
    • Select “1” Controller
    • Select “3” Chan, SDLC
    • Select “9” IO Mapping
    • Select “1” IO Logic
    • Move the cursor down to find an open row (the first 4 rows were used to re-map veh calls to ped calls previously)
    • Set according to table:

• Press “ENTR” key to save

• Map Flash Logic to Terminal and Facilities BIU 2 Ouput

  • Main Menu
  • Select “1” Controller
  • Select “3” Chan, SDLC
  • Select “9” IO Mapping
  • Select “2” IO Map
  • Move cursor to the right twice to edit BIU 2
  • Move cursor down to row 36
  • Set the output code to 230

• Press “ENTR” key to save.

Trafficware Remap Desk Instructions PDF

Revision 0.1