Re-map Desk Instructions - PEEK
When an iCCU-S/S2 system is operating in SDLD/BIU mode, the traffic controller must be remapped for it to see pedestrian calls over BIU. Use the following procedure for PEEK 3000/3000E traffic controllers:
Configure Detector Rack BIU for Pedestrian Calls
- Add the detector rack BIU to match the BIU number configured in the iCCU-S. BIU-1, 2, 3, and 4 on iCCU-S correspond to DET BIU 9, 10, 11 and 12 on traffic controller, respectively.
- Navigate to the PORT 1 SETUP menu and enable the DET BIU.
- Detector Rack BIU Re-mapping
- Selection 3 on the BIU I/O Mapping Menu displays a series of screens where input signals can be assigned.
- If the iCCU-S is configured or Detector BIU 3, map the input as follows:
| PD01 |
PD02 |
PD03 |
PD04 |
PD05 |
PD06 |
PD07 |
PD08 |
| 0 |
B092 |
0 |
B101 |
0 |
B102 |
0 |
B111 |
| OR |
OR |
OR |
OR |
OR |
OR |
OR |
OR |
| 0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
(PD: Puts vehicle call when activated)
- For BIU 9 (Detector BIU 1 on iCCU)
| I/O Code |
DEFAULT |
FUNCTION |
IDX |
| 9092 |
CHN 1 CALL |
PEDESTRIAN DETECTOR |
2 |
| 9101 |
CHN 2 CALL |
PEDESTRIAN DETECTOR |
4 |
| 9102 |
CHN 3 CALL |
PEDESTRIAN DETECTOR |
6 |
| 9111 |
CHN 4 CALL |
PEDESTRIAN DETECTOR |
8 |
| 9112 |
CHN 5 CALL |
PEDESTRIAN DETECTOR |
1 |
| 9121 |
CHN 6 CALL |
PEDESTRIAN DETECTOR |
3 |
| 9122 |
CHN 7 CALL |
PEDESTRIAN DETECTOR |
5 |
| 9131 |
CHN 8 CALL |
PEDESTRIAN DETECTOR |
7 |
- For BIU 10 (Detector BIU 2 on iCCU)
| I/O Code |
DEFAULT |
FUNCTION |
IDX |
| A092 |
CHN 17 CALL |
PEDESTRIAN DETECTOR |
2 |
| A101 |
CHN 18 CALL |
PEDESTRIAN DETECTOR |
4 |
| A102 |
CHN 19 CALL |
PEDESTRIAN DETECTOR |
6 |
| A111 |
CHN 20 CALL |
PEDESTRIAN DETECTOR |
8 |
| A112 |
CHN 21 CALL |
PEDESTRIAN DETECTOR |
1 |
| A121 |
CHN 22 CALL |
PEDESTRIAN DETECTOR |
3 |
| A122 |
CHN 23 CALL |
PEDESTRIAN DETECTOR |
5 |
| A131 |
CHN 24 CALL |
PEDESTRIAN DETECTOR |
7 |
- For BIU 11 (Detector BIU 3 on iCCU)
| I/O Code |
DEFAULT |
FUNCTION |
IDX |
| B092 |
CHN 33 CALL |
PEDESTRIAN DETECTOR |
2 |
| B101 |
CHN 34 CALL |
PEDESTRIAN DETECTOR |
4 |
| B102 |
CHN 35 CALL |
PEDESTRIAN DETECTOR |
6 |
| B111 |
CHN 36 CALL |
PEDESTRIAN DETECTOR |
8 |
| B112 |
CHN 37 CALL |
PEDESTRIAN DETECTOR |
1 |
| B121 |
CHN 38 CALL |
PEDESTRIAN DETECTOR |
3 |
| B122 |
CHN 39 CALL |
PEDESTRIAN DETECTOR |
5 |
| B131 |
CHN 40 CALL |
PEDESTRIAN DETECTOR |
7 |
- For BIU 12 (Detector BIU 4 on iCCU)
| I/O Code |
DEFAULT |
FUNCTION |
IDX |
| C092 |
CHN 49 CALL |
PEDESTRIAN DETECTOR |
2 |
| C101 |
CHN 50 CALL |
PEDESTRIAN DETECTOR |
4 |
| C102 |
CHN 51 CALL |
PEDESTRIAN DETECTOR |
6 |
| C111 |
CHN 52 CALL |
PEDESTRIAN DETECTOR |
8 |
| C112 |
CHN 53 CALL |
PEDESTRIAN DETECTOR |
1 |
| C121 |
CHN 54 CALL |
PEDESTRIAN DETECTOR |
3 |
| C122 |
CHN 55 CALL |
PEDESTRIAN DETECTOR |
5 |
| C131 |
CHN 56 CALL |
PEDESTRIAN DETECTOR |
7 |
PEEK Remap Desk Instructions PDF
Revision 0.1
